{"product_id":"hb-body-plastofix-p340-plastic-primer-adhesion-promoter","title":"HB BODY PLASTOFIX P340 plastic primer \/ adhesion promoter","description":"\u003cp\u003e\u003cstrong\u003eHB BODY P340 PLASTOFIX\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eis a clear plastic primer (adhesion promoter) for plastic car parts available in spray can or 500ml metal can. P340 plastofix goes on first as a thin, invisible layer that the primer and paint can hold on to, so the repair does not peel or chip later. It also works on metal parts and on filler if additional adhesive layer is necessary. Ready to use.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWorks on many surfaces - all car plastics except pure polyethylene (PE).\u003c\/li\u003e\n\u003cli\u003eQuick to work with: You can paint over it after only 10 minutes at 23°C (73°F), using any acrylic or epoxy primer and topcoat.\u003c\/li\u003e\n\u003cli\u003eThe layer is transparent and has no effect on the paint shade on top.\u003c\/li\u003e\n\u003cli\u003eOne litre covers about 30 to 35 m² at 10 microns dry film thickness.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eP340 PLASTOFIX Directions for use\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean the part:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eThe surface must be dry and clean, with no grease, wax or dirt on it. Keep it clean and dry at every step that follows.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSand if needed:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eMetal parts and polyester filler need to be sanded first with a suitable grit paper. Bare plastic parts do not need sanding, only cleaning.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDegrease:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eWipe the surface with degreaser. Use two cloths: one to wipe the cleaner on, one to wipe it off. Always wipe it off while it is still wet, using a clean dry cloth.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemove dust:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eBlow the part with clean air, then wipe it with a tack cloth to pick up the last dust.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGet the product ready:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eShake the tin or can well. Nothing else is needed, the product is ready to use.\u003c\/li\u003e\n\u003cli\u003eApply 2 very thin coats. Together they should give 20 to 30 microns (0.8 to 1.2 mil) of dry film, which is a very thin layer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWait between coats:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eLeave 5 minutes at 23°C (73°F) after the first coat before you spray the second one.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePaint over it:\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eAfter 10 minutes at 23°C (73°F) you can apply any primer and topcoat.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eP340 PLASTOFIX Care \u0026amp; safety instructions\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eThis is a professional product. Always wear protective equipment and work in a room with good airflow.\u003c\/li\u003e\n\u003cli\u003eRead the safety data sheet (MSDS) and the warnings on the label before you start.\u003c\/li\u003e\n\u003cli\u003eDo not use it when the temperature is below 10°C (50°F).\u003c\/li\u003e\n\u003cli\u003eDo not use it on pure polyethylene (PE) parts. It will not grip properly on that plastic.\u003c\/li\u003e\n\u003cli\u003eDo not thin it. Adding thinner or reducer will weaken how well it grips.\u003c\/li\u003e\n\u003cli\u003eStore it in the original unopened tin in a cool place, 5 to 25°C (41 to 77°F). It keeps for 24 months.\u003c\/li\u003e\n\u003cli\u003eSpecific gravity: 0.87 ± 0.02 g\/cm³. Solid content: 5 ± 2% by weight.\u003c\/li\u003e\n\u003cli\u003eVOC (2004\/42\/EC): category IIB(a), limit 850 g\/L. This product contains 850 g\/L ready for use.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"HB BODY","offers":[{"title":"Default Title","offer_id":53843071402331,"sku":"HB5100000010","price":13.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0990\/1146\/1467\/files\/hb-body-p340-plastic-primer-plastofix-adhesion-promoter.png?v=1787232340","url":"https:\/\/trauto.eu\/products\/hb-body-plastofix-p340-plastic-primer-adhesion-promoter","provider":"trauto.eu","version":"1.0","type":"link"}