CAR-REP

Car-rep RUBBERcomp® rubber paint is a multi-purpose, air drying rubber coating. spray-can volume 400ml. It protects against moisture, acids, abrasion, corrosion and slip/slipperiness, and provides a comfortable, controlled grip. RUBBERcomp® remains flexible and stretchy over time, and will not crack or become brittle in extreme weather conditions, long lasting when painted on a surface with suitable adhesion. Easy to peel off. It has been tested and proven at temperatures from -30°C to +90°C. Four layers of rubbercomp paint are required for sufficient film thickness. For other shades, packaging types for CAR-REP Rubbercomp contact the store in person or by email.

Read more less

Car-rep Hollow Section is a wax-based protection for your car's doors and sill panels, underbody interior sections. Spray-can total volume 500ml. Applied through the technical holes with a special spray tube. It penetrates the smallest gaps, removing moisture and protecting against rust. Instructions: Cover all surfaces that do not need to be treated. Shake the spray approx. 3 minutes before use. Spray several thin layers, allowing the wax to dry between sprays.

Read more less

CAR-REP Brake Caliper Spray is a special paint for brake calipers. It leaves a shiny, heat-resistant surface with anti-corrosion properties. Spray can volume 400ml (should be enough for all 4 brake calipers). Clean the surface with a steel brush or sandpaper. Remove dust, grease with a degreaser. Protect and cover parts around. Shake the aerosol for about 3 minutes, spray from about 20-30 cm distance. First spray a very light thin layer, wait 5-10 mins at 20 degrees Celsius and repeat.

Read more less

CAR-REP Stone Chip spray 500 ml is a 1k anti-chipping coating for visible parts that need additional protection. Available in white, gray and black. Must be overpainted or added as . CAR-REP Stone chip spray application guide The surface to be painted must be clean, degreased and dry - either primed or if existing, previous paint layer matted. Make sure you protect adjacent surfaces that will not be painted by covering/masking them. Shake the bottle for at least 2 minutes, even after the mixing beads have separated from the bottom of the bottle, and also occasionally during painting. During painting, hold the bottle in a vertical position, approximately 30 cm from the surface to be painted. Apply 2-3 thin coats to the surface, allow each coat to dry for 3-5 minutes, but no longer than 30 minutes. To clean the nozzle, turn the spray upside down and spray until only compressed air comes out of the bottle, so the spray can be reused.

Read more less

Car-Rep® Grease Off is a degreaser and cleaner spray - volume 500ml. Removes oil, grease, low stickiness wax and is also suitable for brake and clutch surfaces. Should be used by spraying the product and wiping with a degreasing cloth.

Read more less

CAR-REP Anti-rust primer spray is a high quality, fast drying acrylic 400 ml spray primer. Suitable for almost all surfaces such as metal, wood, hard plastic, stone, concrete, glass, vinyl and many other materials. It is recommended to mechanically clean the surface from rust before priming to ensure longer corrosion protection. Prior to priming plastic suggested to apply another layer of plastic primer. Shake the spray for about 2 minutes, spray from a distance of about 20-30 cm, 2-3 layers, 10-15 min between layers at 20 degrees Celsius. One spray can is ~ for 1 small body panel - fender, door (~1m2). Bumpers, hood, roof require 2-3 spray cans for cars, and more for vans.

Read more less

CAR-REP AcrylComp clearcoat spray, total volume 500ml, appropriate for 2 layers of clearcoat on 1 square meter or approx. 1 small body panel - (door, fender, etc.). Bumper, hood, boot requires at least 2 for most cars. CAR-REP clearcoat application Sand, clean, degrease the surface if necessary. Remove dust. Shake the can for 2-3 min. Test on a hidden area. Spray from 15 cm distance, starting outside the object to be painted, as small drops may form at the beginning of spraying. Apply a light first coat, repeat after 15 min with a slightly thicker coat, after which the finish should be glossy right after applying, but the clearcoat does not start forming drops. Provides surface wear resistance and scratch protection - sensitive to solvents.  

Read more less