Underbody coatings

Multifuller UBS anti-gravel coating spray, spray can total volume 500 ml. Forms a strong and elastic coating that protects against mechanical damage. Used on visible parts that need additional protection. Available in white, gray and black. Must be over sprayed with paint or clearcoat.  It is recommended to wear protective clothing and goggles during painting.  Apply 2-3 thin coats to the surface. Allow each coat to dry for 3-5 minutes, but no longer than 30 minutes. After use, to clean the nozzle, turn the spray upside down and spray until only compressed air comes out of the spray. After ~1.5H of drying, cover with a base or acrylic paint in the appropriate shade, must be over sprayed. Multifuller UBS antigravel Coating Product Description and Technical Data Sheet in English

Read more less

Car-rep Hollow Section is a wax-based protection for your car's doors and sill panels, underbody interior sections. Spray-can total volume 500ml. Applied through the technical holes with a special spray tube. It penetrates the smallest gaps, removing moisture and protecting against rust. Instructions: Cover all surfaces that do not need to be treated. Shake the spray approx. 3 minutes before use. Spray several thin layers, allowing the wax to dry between sprays.

Read more less

Anti-corrosion protection agent RADEX 210 UBC on bitumen base for the underbody treatment - car body floor and wheel arches. 1l package for UBC spray gun. After drying, it retains a sticky layer that protects against salts, moisture, corrosion and mechanical damage, such as stone impacts. Shake well before use, mechanically remove rust, clean surface, degrease. Applied with UBS gun. Apply 1-2 layers with 15-30 min pause at 20 degrees Celsius. Full drying time 4-6 hours, but will always have a slightly sticky layer.

Read more less

RADEX 701 One-component polyurethane sealant - 290 ml, available in white, gray and black. Fast-curing and flexible sealant for sealing the car body, weld connections. For use with a caulking gun. Specially formulated to meet the demands of the automotive industry. The sealant has a controlled viscosity and is easy to smooth with a brush or rubber blade if a thin sealant layer is required. It is repaintable after surface curing.

Read more less

CAR-REP Stone Chip spray 500 ml is a 1k anti-chipping coating for visible parts that need additional protection. Available in white, gray and black. Must be overpainted or added as . CAR-REP Stone chip spray application guide The surface to be painted must be clean, degreased and dry - either primed or if existing, previous paint layer matted. Make sure you protect adjacent surfaces that will not be painted by covering/masking them. Shake the bottle for at least 2 minutes, even after the mixing beads have separated from the bottom of the bottle, and also occasionally during painting. During painting, hold the bottle in a vertical position, approximately 30 cm from the surface to be painted. Apply 2-3 thin coats to the surface, allow each coat to dry for 3-5 minutes, but no longer than 30 minutes. To clean the nozzle, turn the spray upside down and spray until only compressed air comes out of the bottle, so the spray can be reused.

Read more less

Radex BS Seal is a one-component synthetic rubber sealant for seams in 1kg metal can. The Quickly forms an elastic textured coating similar to the original seams. Radex BS Seal seam sealant has good mechanical strength, excellent anti-corrosion and soundproofing properties. The product has resistance to water, oil, gasoline. product is very easy to apply with a mastic brush (must have stiff bristles, as it is very thick). Brushes not included.

Read more less

RADEX 901 spray sealant is a beige or grey one-component moisture-curing coating based on modified silane polymer with high mechanical strength in a 290ml bottle and to be applied with PGS sealant spray gun. It provides excellent corrosion protection. RADEX 901 application areas - welds and welded joints, forming flexible anti-chipping coatings on the bottom of cars.

Read more less

RADEX ML 110 is a non-paintable transparent elastic wax coating 1l bottle. It has excellent anti-corrosion properties. The internal cavity wax perfectly displaces water and can be applied even to damp surfaces, but it is recommended to apply it to as dry internal surfaces as possible. After drying, the coating remains slightly sticky and elastic without a specific smell. Apply with a anti-gravel gun with an extended spray tube through the technical holes on the internal surfaces of the car body panels and sills, to protect the car from rusting for a longer period of time.

Read more less

Radex 310 SP is a sprayable anti-stone chip protective mastic made of synthetic rubber and resins in a 1l bottle supposed to be used with anti-gravel spray guns. Available in black, grey and white. Quickly creates a structured protective coating (usually on sills and on the wheel arches, locations where a painted protective layer is necessary. Must have a paint or clearcoat layer applied over it to have full protection capabilities. 

Read more less

Noxudol UM-1600 is a fibre reinforced product for underbody treatment. 1 liter bottle for anti-gravel spray gun. A thicker layer provides a good sound damping effect. The product consists of bitumen, waxes and solvents. Noxudol UM-1600 is a durable anti-corrosion product used under the wings, inside the wheel arches and the rest of the underside of the car body where extra effective protection is needed. Noxudol UM-1600 TDS technical product info

Read more less

Mercasol 9 is a wax and oil-based anti-rust coating that penetrates deep into the pores after spraying for long-lasting rust resistance. 1 liter bottle for anti-gravel spray gun. It can also be applied to surfaces with superficial rust, but this can allow the surface to rust again more quickly. After application, it leaves a sticky surface, which must be covered with a subsequent layer of protective material (wax, anti-corrosion coating, bitumen).

Read more less

 Mercasol 3AL is a bronze-colored, wear resistant underbody corrosion protection agents, based on bitumen and wax. Spray-can 600ml total volume, bottle 1l net volume. The product has corrosion protection properties over a long period of time. Used on the underbody and in the wheel houses of vehicles in order to protect from stone chips and corrosion. The film properties of Mercasol 3 prevent them from being chipped off by e.g. gravels. The products have been compatibility tested with most corrosion protection systems. Ordering a full box (12 pcs) or more, a discount is available. Mercasol 3AL - technical product data sheet

Read more less

Mercasol 3BL is a black, wear resistant underbody corrosion protection agents, based on bitumen and wax. Spray-can 600ml total volume, bottle 1l net volume. The product has corrosion protection properties over a long period of time. Used on the underbody and in the wheel houses of vehicles in order to protect from stone chips and corrosion. The film properties of Mercasol 3 prevent them from being chipped off by e.g. gravels. The products have been compatibility tested with most corrosion protection systems. Ordering a full box (12 pcs) or more, a discount is available. Mercasol 3BL - technical product data sheet

Read more less

Mercasol 2 is a solvent-based transparent anti-corrosion protection product that leaves a completely dry and non-sticky surface. Based on wax and sulfonates, provides long-term protective properties. Mercasol 2 is mainly used on visible surfaces where a dry, non-tacky, discreet protective layer is required, for example on vehicle doors and hoods, or on tools and equipment. Mercasol 2 can also be used as anti-corrosion protection in joints and connection points. Mercasol 2 application suggestions The surfaces to be treated must be dry and free from rust, dirt, salt, and oil. Application should be carried out indoors at a temperature between +15°C and +25°C. Mercasol 2 1-liter bottle is intended for use with a compressed air spray gun together with a cavity hose. Mercasol 2 aerosol is applied using the attached nozzle and tube. When applying with an aerosol, two coats may be required to achieve the recommended dry film thickness, as the applied layer is finer compared to spraying with a gun. Mercasol 2 technical data sheet in English.

Read more less

Mercasol 1 is a thin, solvent-based, easy-to-spray anti-corrosion liquid based on wax, sulfonate and oil for internal surfaces (sills, door frames, etc.). 600ml total volume spray can and 1l net volume bottle for use with anti-gravel gun. The product has very good anti-corrosion properties for a long time if the surface is prepared correctly. The wax dries to a brown, oily, moisture-repellent coating. Mercasol 1 has been tested for compatibility with the most common anti-corrosion protection systems on the market. Mercasol 1 is intended for the protection of vehicle cavities, flanges and joints against corrosion. Mercasol 1 can also be used as a primer on exposed surfaces in combination with Mercasol 3 and 3AL underbody corrosion protection products. Mercasol 1 application guide The surfaces to be treated must be dry and free of rust, dirt, salt and oil. The 1 liter bottle of Mercasol 1 is primarily intended for use with a compressed air gun. Mercasol 1 aerosol is applied with the nozzles provided in the package. Application should be carried out indoors at a temperature of +15 to +25°C. Drying time depends on temperature and humidity, at +23°C and 50% RH, drying time is approx. 8 h. If Mercasol 3 or Mercasol 3AL is planned to be used, Mercasol 1 must be allowed to dry for 1 hour before applying Mercasol 3 or Mercasol 3AL. Mercasol 1 technical data sheet in English

Read more less